Laurel-electronics LAUREATE SERIES 2 COUNTER-TIMER-SERIAL INPUT METER Manual de usuario descargar pdf (Pagina 52)

Press

Press Digit

Select Key

Press Value Select

Key

dSPyno

Display #

____01 PEAK key action

0 Display Peak 1 Display Valley

2 Peak (1

push), Valley (2

push)

____01 Item to display

after Meter Reset

1 Item #1* (Quadrature Rate = Rate A - Rate B)

2 Item #2* (Rate A) 3 Item #3* (Rate B)

GAtE_t

Gate time*

_000.00 _000.00 _000.00

_000.00 _000.00

Select digit to flash.

Select 0 thru 9 for flashing digit to set gate time* in

seconds. Decimal point location is fixed for 10 ms

resolution.

.ti_Out.

Time-out*

_000.00 _000.00 _000.00

_000.00 _000.00

Select digit to flash.

Select 0 thru 9 for flashing digit to set time-out* in

seconds. Decimal point location is fixed for 10 ms

resolution.

FiLtEr

Filtering

_00000

Signal filtering

0 Adaptive moving average filter. Restarts filter for

high actual changes in signal.

1 Conventional moving average filter without reset.

_00000

Peak & Valley filtering

0 Peak* or Valley* value from unfiltered signal.

1 Peak* or Valley* value from filtered signal.

_00000

Display filtering

0 Display value of unfiltered signal.

1 Display value of filtered signal.

_00000

Adaptive filter setup

0 Set adaptive filter for normal noise.

1 Set adaptive filter for presence of high transients.

_00000

Filter time constant

0 No filter 1 0.1 sec 2 0.2 sec 3 0.4 sec

4 0.8 sec 5 1.6 sec 6 3.2 sec 7 6.4 sec

dEC.Pt1

Decimal pt1

11111

Decimal point flashes.

11111 11

1111 111

111 1111

11 11111

1 111111

Press to shift decimal point of reading.

dEC.Pt22

Decimal pt2

22222

Decimal point flashes.

Make the same as dEC.Pt1

Scale and Offset scaling method if selected under SEtuP

SCALE1

Scale

Factor 1

0.00000 0.00000 0.00000

Select the digit to flash

for the Scale Value, then

press one more time

for the Scale Multiplier.

Select -9 thru 9 for flashing first digit and 0 thru 9 for

other flashing digits. This will set the Scale Value*

from -9.99999 to 9.99999 with a fixed decimal point.

Then press to select a value from 0.00001 to

100000 in decade steps for the Scale Multiplier.

Scale Factor = Scale Value x Scale Multiplier.

OFFSt1.

Offset 1

000000 000000 000000

Select digit to flash.

Select -9 thru 9 for flashing first digit and 0 thru 9 for

other flashing digits. Use dEC.Pt1 to set the decimal

point.

SCALE2 Scale Factor 2 Make the same as SCALE1.

OFFSt2. Offset 2 Make the same as OFFSt1.

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 79 80

Comentarios a estos manuales

Sin comentarios

Laurel-electronics LAUREATE SERIES 2 COUNTER-TIMER-SERIAL INPUT METER Manual de usuario Pagina 52

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Laurel-electronics LAUREATE SERIES 2 COUNTER-TIMER-SERIAL INPUT METER